Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- shelly [09/05/2024 - 17:55] – [Plug S] admin
+++ shelly [09/05/2024 - 17:59] (aktuell) – [Plug S] admin
@@ Zeile 2: / Zeile 2: @@
 The normal mode of the device is its typical operational state when powered on, free from alarms, updates, calibrations, or ongoing configuration changes. **LED blinking**: In normal mode, the LED will blink **0,5 sec on, 2 sec off** to indicate the device's status. The LED colours and patterns will depend on whether the device is included or excluded from the network, as well as whether it is calibrated or not.
-===== Plug S =====
+====== Plug S ======
-**Green**: This LED colour pattern indicates that the device is **added (****included)** in the network.
+  *
-**Red** **SOLID ON**: **Settings mode**
+When plugged for the first time:
-The Settings mode is an alternate operational state that can be accessed by pressing the designated service button (S button). This mode enables users to add, remove, reset or calibrate the device.
+      *
-**LED solid on**: When the device is in settings mode, the LED will remain solidly lit to indicate the device's status. The LED colours will depend on the action being taken.
+Blue light flashing, indicating AP mode.
-**Blue**: This LED colour is used for **adding** (inclusion) or **removing** (exclusion) of the device from the network.
+  *
+When plugged/powered again after being successfully connected to a Wi-Fi network:
+      *
+Red light flashing, indicating the the Device is reconnecting to the Wi-Fi network.
+      *
+Constant red light, indicating that the Device cannot reconnect to the Wi-Fi network.
+**Green**: This LED colour pattern indicates that the device is **added (****included)**  in the network.
+**Red**  **SOLID ON**: **Settings mode**
+The Settings mode is an alternate operational state that can be accessed by pressing the designated service button (S button). This mode enables users to add, remove, reset or calibrate the device.** **When the device is in settings mode, the LED will remain solidly lit to indicate the device's status. The LED colours will depend on the action being taken.
+**Blue**: This LED colour is used for **adding**  (inclusion) or **removing**  (exclusion) of the device from the network.
 **Red**: This LED colour is used for a **factory reset**.
-**Settings in progres:** The next state involves executing the selected setting. To start this mode is required releasing the S button momentarily and promptly pressing it again while you're in the setting you want to trigger.
+**Settings in progres:**  The next state involves executing the selected setting. To start this mode is required releasing the S button momentarily and promptly pressing it again while you're in the setting you want to trigger.
-**LED blinking**: In settings in progres, the LED will blink **0,1 sec on, 0,1 sec off** to indicate the setting being executed. The LED colours and patterns will depend on the selected setting.
+**LED blinking**: In settings in progres, the LED will blink **0,1 sec on, 0,1 sec off**  to indicate the setting being executed. The LED colours and patterns will depend on the selected setting.
-**Blue**: This LED colour indicate that the **adding** (inclusion) or **removing** (exclusion) of the device is in progres.
+**Blue**: This LED colour indicate that the **adding**  (inclusion) or **removing**  (exclusion) of the device is in progres.
 **Red **:**factory reset **is in progres.
+==== Control button ====
+  *
+Press to turn On/Off the output.
+  *
+Press and hold 3 sec to check status (Possible only when the output in Off).
+  *
+Press and hold 5 sec to reboot (Possible up to 60 sec after plugging the Device).
+  *
+Press and hold 10 sec to factory reset (Possible up to 60 sec after plugging the Device).